twinenote9

Fiat 500 Replacement Key Fob If your 500 remote key fob has stopped functioning, it could be time to replace the battery. However, if you replace the battery and it continues to stop working then the issue may be elsewhere. At United Locksmith, we specialize in making new keys for classic automobiles. We have the tools as well as the parts needed for this job. Dead Coin Battery A dead battery is the most common reason for your Fiat 500 keyfob not locking or unlocking the doors. The coin cell battery in the key fob is likely to drain quickly when you don't use it often enough. If your remote starts to show signs of a loss of range or has stopped working or not responding, then the battery could be dead. Metal clips keep the battery in inside the key fob. If the clips aren't tight enough, it can cause contact issues that will stop the remote from receiving power. Use a flathead screwdriver to open the retaining clips and remove the battery. Use a battery that has the same voltage, size and specifications as the original. G28 can also cause the key fob to become corroded or damaged. Even a small bath in soapy water may harm the electronic chip within. It is recommended to keep your key fob in a dry place. Water Damage Water damage could be the reason behind your key fob not functioning properly. Key fobs are fitted with rubber seals that protect them from being damaged by a light rain or splashes of water, however it is essential to keep your car keys out of the pool, ocean, and the washing machine! The key fob is equipped with an electronic chip that sends a message to the immobilizer system in your car. This is the reason why your 500 can start or lock, but when the chip becomes wet, it will no longer work. You can try cleaning your key fob's internal electronics with isopropyl alcohol or an electronic cleaner to determine whether they're still functioning. However, it is probably better to purchase a replacement from a dealership rather than trying to repair the key fob which was submerged in salt water. A replacement fob might cost you a little bit however, it's less expensive than paying to have your Fiat 500 towed to a dealership and fixed there! You could also do it yourself with just a few steps. Make sure you have the correct type of battery before you attempt to open your key fob. This task is far simpler than it appears and there are step-by-step instructions online for virtually any key fob for cars. Faulty Chip The chip inside the key fob communicates directly with the immobiliser on your car to ensure that the vehicle will only start when right keys are in place. If the chip is damaged or destroyed the car will not start regardless of what you do. Damage to the water or a dead phone battery are the most common causes of defective chips. Regardless of the reason, it's recommended to delegate this task to a locksmith who will be able to replace the chip for you swiftly and at a reasonable cost. If your key fob fails to function after exposure to clean water from the tap or rain, take out the battery and wipe down the electronic component with a towel to ensure it is fully dry before putting it back into. If the key fob doesn't work it's likely to be a fried chip and must be replaced. Some people will go to their dealer in order to get an entirely new Fiat fob. However, this can be an expensive option. If you're looking for a low-cost solution to have your Fiat key fob fixed, look no further than United Locksmith. We have the tools and expertise necessary to repair your Fiat key fob in a quick and professional way. Faulty Receiver Module Fiat key fobs transmit signals up 50 feet to the vehicle, which allows it to unlock and close the doors (and start the vehicle in case of automatic transmissions). There are a variety of reasons why the fob might stop working. These include a dead coin battery damaged by water, worn buttons, a receiver module issue and signal interference, or an electronic chip that has failed. If the fob has been in a pocket that has experienced extreme trauma, such as being dropped on a hard floor or getting washed in the washing machine the fob may not be capable of communicating with the car's Body Control Module (BCM). The BCM is a security system which will only accept signals from genuine keys. You will need to replace the fob in case this happens. A professional locksmith will take care of the entire process of replacing your key including programming a brand new key for your 500. They can even offer the fob cloned to work just like the original (and costs less than what it would cost).